 |
 |
|
IC
Controller |
|
|
|
Model
No. |
C-239-2 (For 110V)
, C-239-4 (For 220V)
|
|
Description |
LED Display IC Controller
(Water quality will be detected automatically) |
|
Size |
(L)35mm
x (W)125mm x (H)100mm |
|
Specification |
 |
It will wash automatically for 45 seconds when it used at the first time ; it will not work if its supply pressure is inadequate. |
|
When the power is on, the red light is on. (Red light represents power) |
|
Importing water detection (green light): When the water comes, switched on the low pressure switch delays for 5 seconds. |
|
When the source water is on, the green light is on. (Green light represents source water) |
|
When the green light is on, the pump starts to produce water and the red light is on. |
|
Full water detection(green light): When water is full the high pressure switch delays for 5 seconds. |
|
The pump will stop producing water, red light is off; green light is on. |
|
Auto wash (yellow light):
It will wash automatically for 45 seconds when the pressure tank is full.
[FLUSH] yellow light
[TANK FULL] green light
[POWER] red light
[Producing Water] 4 red light on at the same time. |
|
Reaction of pump (red light): It can shine when producing water. |
|
Water quality: Detecting range produce water ratio 85% กำ5% CLEAN.
00-04 ppm shown on the LED is the normal range; if the water quality is more than 04 ppm, the LED will show 99 ppm and keep shining red light on the LED, means please replace the RO Membrane. |
|
Notice: The detecting of water quality is normal according to formal producing water. It should be wipe with alcohol per 3 ~ 4 month. |
|
IC
Controller |
|
|
Model
No. |
C-237 (For 110V) ,
C-237-1 (For 220V) |
Description |
IC Controller (No LED) |
Size |
(L)35mm
x (W)125mm x (H)100mm |
Specification |
|
IC Controller (No LED). |
|
It will wash automatically for 45 seconds when it used at the first time ; it will not work if its supply pressure is inadequate. |
|
When the power is on, the red light is on. (Red light represents power) |
|
Importing water detection (green light): When the water comes, switched on the low pressure switch delays for 5 seconds. |
|
When the source water is on, the green light is on. (Green light represents source water) |
|
When the green light is on, the pump starts to produce water and the red light is on. |
|
Full water detection(green light): When water is full the high pressure switch delays for 5 seconds. |
|
The pump will stop producing water, red light is off; green light is on. |
|
Auto wash (yellow light):
It will wash automatically for 45 seconds when the pressure tank is full.
[FLUSH] yellow light
[TANK FULL] green light
[POWER] red light
[Producing Water] 4 red light on at the same time. |
|
Reaction of pump(red light): It can shine when producing water.. |
|
|
IC
Controller ( Liquid Crystal Display)
|
|
|
|
Model
No.
|
C-239 (For 110V)
C-239-1 (For 220V)
|
|
Description
|
IC
Controller ( Liquid Crystal Display)
|
|
Size
|
(L)35mm
x (W)125mm x (H)100mm
|
|
Specification
|
|
It will wash RO Membrane automatically for 60 seconds when it used at the first time; it will not work if its supply pressure is inadequate. |
|
If the source water and power are on, the IC controller will detect the system around 60 seconds and there will be 5 lights shining, green [Full], Orange [Flush], Red [Producing water], Green [Source water], and Orange [Manual]. |
|
After that, the number shown on the LED will start to count down from 60 to 0.
When detecting after 20 seconds, there will be three kinds of different results.
|
|
When detected producing water status, the Green light [Source] and Red light [Producing Water] will be on to show the insufficient water in the Tank. |
|
When detected a shortage of water or no water, the Green Light [Source] will be shining. |
|
When detected full water status, the Green light [Source] and the Green Light [Full] will be on; Red light [Producing Water] will be off. |
|
Every 24 hours, the IC controller will wash RO Membrane automatically around 50- 60 seconds. Every automatical washing has two reactions.
(A) If auto washing is started under the function of full water, then there will be four lights on, Orange [Manual], Green [source], Orange [Flush] and Green [Full].
(B) If auto washing is started under the function of producing water, then there will be four lights on, Orange [Manual], Green [source], Orange [Flush] and Red [work].
(If press RESET, the IC Controller will restart the auto detecting function and the time of producing water will be zero for another calculation.) |
|
Reaction of pump(red light): It can shine when producing water. |
|
Water quality: Detecting range produce water ratio 85% กำ5% CLEAN. 00-04 ppm shown on the LED is the normal range; if the water quality is more than 04 ppm, the LED will show 99 ppm (Sometimes 05-99ppm, it depends on the ppm of the source water.) and keep shining red light on the LED, means please replace the RO Membrane. |
|
Notice: The detecting of water quality is normal according to formal producing water. It should be wipe with alcohol per 3 ~ 4 month. |
|
|
|
